<div dir="auto">Have you considered wire EDM?</div><div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Thu, Jun 9, 2022 at 18:40 Hathaway, Malcolm R <<a href="mailto:hathaway@cns.fas.harvard.edu">hathaway@cns.fas.harvard.edu</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left-width:1px;border-left-style:solid;padding-left:1ex;border-left-color:rgb(204,204,204)">




<div dir="ltr">
<div style="font-family:Calibri,Arial,Helvetica,sans-serif;font-size:12pt;color:rgb(0,0,0)">
This would seem to be a good application for electron beam sectioning or milling.</div>
<div style="font-family:Calibri,Arial,Helvetica,sans-serif;font-size:12pt;color:rgb(0,0,0)">
<br>
</div>
<div style="font-family:Calibri,Arial,Helvetica,sans-serif;font-size:12pt;color:rgb(0,0,0)">
Alternately, I'm told water jet milling can cut pretty thick sections and leave a reasonably clean cut.  Not sure if it (the water spraying around) would be too violent for your surface to be analyzed.
<br>
</div>
<div style="font-family:Calibri,Arial,Helvetica,sans-serif;font-size:12pt;color:rgb(0,0,0)">
<br>
</div>
<div style="font-family:Calibri,Arial,Helvetica,sans-serif;font-size:12pt;color:rgb(0,0,0)">
I'm sure others more knowledgeable will be weighing in...</div>
<div style="font-family:Calibri,Arial,Helvetica,sans-serif;font-size:12pt;color:rgb(0,0,0)">
<br>
</div>
<div style="font-family:Calibri,Arial,Helvetica,sans-serif;font-size:12pt;color:rgb(0,0,0)">
<br>
</div>
<div style="font-family:Calibri,Arial,Helvetica,sans-serif;font-size:12pt;color:rgb(0,0,0)">
Mac</div>
<div style="font-family:Calibri,Arial,Helvetica,sans-serif;font-size:12pt;color:rgb(0,0,0)">
Harvard CNS<br>
</div>
<div style="font-family:Calibri,Arial,Helvetica,sans-serif;font-size:12pt;color:rgb(0,0,0)">
<br>
</div>
<div id="m_-3862499422901534391appendonsend"></div>
<hr style="display:inline-block;width:98%">
<div id="m_-3862499422901534391divRplyFwdMsg" dir="ltr"><font face="Calibri, sans-serif" style="font-size:11pt;font-family:Calibri,sans-serif;color:rgb(0,0,0)"><b style="font-family:Calibri,sans-serif">From:</b> labnetwork <<a href="mailto:labnetwork-bounces@mtl.mit.edu" target="_blank" style="font-family:Calibri,sans-serif">labnetwork-bounces@mtl.mit.edu</a>> on behalf of Beall, James A. (Fed) <<a href="mailto:james.beall@nist.gov" target="_blank" style="font-family:Calibri,sans-serif">james.beall@nist.gov</a>><br>
<b style="font-family:Calibri,sans-serif">Sent:</b> Thursday, June 9, 2022 3:09 PM<br>
<b style="font-family:Calibri,sans-serif">To:</b> <a href="mailto:labnetwork@mtl.mit.edu" target="_blank" style="font-family:Calibri,sans-serif">labnetwork@mtl.mit.edu</a> <<a href="mailto:labnetwork@mtl.mit.edu" target="_blank" style="font-family:Calibri,sans-serif">labnetwork@mtl.mit.edu</a>><br>
<b style="font-family:Calibri,sans-serif">Subject:</b> [labnetwork] Wire saw cross sectioning service</font>
<div> </div>
</div>
<div><font size="2" style="color:rgb(0,0,0)"><span style="font-size:11pt">
<div>Hello,<br>
<br>
We are fabricating micro machined silicon feedhorns (stacked silicon platelets that are gold plated) that we would like to have cross sectioned to analyze the final horn profile and gold plating quality. The parts a 1.5 cm x 2 cm x 2 cm and the waveguide ID
 ranges from 0.5 - 3 mm.<br>
<br>
I’ve done this in the past with a low speed Buehler diamond blade saw followed by lapping but it is hard to hit the diameter of the waveguide and is tedious to lap down.<br>
<br>
Ted Pella and Princeton Scientific sell ~$10K wire saws which would probably work but for only a couple of samples we are looking for a company that might perform this device.<br>
<br>
Any recommendations?<br>
<br>
Thanks very much,<br>
<br>
Jim Beall<br>
NIST Boulder<br>
Quantum Sensors Project<br>
Boulder, CO<br>
_______________________________________________<br>
labnetwork mailing list<br>
<a href="mailto:labnetwork@mtl.mit.edu" target="_blank">labnetwork@mtl.mit.edu</a><br>
<a href="https://mtl.mit.edu/mailman/listinfo.cgi/labnetwork" target="_blank">https://mtl.mit.edu/mailman/listinfo.cgi/labnetwork</a><br>
</div>
</span></font></div>
</div>

_______________________________________________<br>
labnetwork mailing list<br>
<a href="mailto:labnetwork@mtl.mit.edu" target="_blank">labnetwork@mtl.mit.edu</a><br>
<a href="https://mtl.mit.edu/mailman/listinfo.cgi/labnetwork" rel="noreferrer" target="_blank">https://mtl.mit.edu/mailman/listinfo.cgi/labnetwork</a><br>
</blockquote></div></div>-- <br><div dir="ltr" class="gmail_signature" data-smartmail="gmail_signature"><div dir="ltr"><div>Brian K. Olmsted<br></div><div>Associate Director of Laboratory Operations<br><div>University of Minnesota | MNC<br><div><a href="http://www.mnc.umn.edu" target="_blank">www.mnc.umn.edu</a></div></div><div>612.626.3287</div><div><a href="mailto:olms0025@umn.edu" target="_blank">olms0025@umn.edu</a></div><div><br></div></div></div></div>