<div dir="ltr"><div class="gmail_default" style="color:#0b5394">Hi Iulian,</div><div class="gmail_default" style="color:#0b5394"><br></div><div class="gmail_default" style="color:#0b5394">We have worked with spin-on dopants from Filmtronics for a number of years both in our cleanroom and in a teaching lab.  The dopants we use contain either boron of phosphorus, and they are essentially a doped spin-on glass.  </div><div class="gmail_default" style="color:#0b5394"><br></div><div class="gmail_default" style="color:#0b5394">We have used these materials in spin coaters that were shared with other resists, and we did not experience much of an issue with mess.  However, it should be noted that the solvents used in both (ethanol or ethylene glycol monoethyl ether) may not be compatible with all resists, so we did try to isolate them to one spinner only, and we were diligent about cleaning out the spinner basins after use just to be safe.  </div><div class="gmail_default" style="color:#0b5394"><br></div><div class="gmail_default" style="color:#0b5394">We also took precautions to prevent cross-contamination during annealing by making sure to use dedicated chambers (in the case of RTA) or furnace tubes.  </div><div class="gmail_default" style="color:#0b5394"><br></div><div class="gmail_default" style="color:#0b5394">Best Regards,</div><div class="gmail_default" style="color:#0b5394"><br>Matt</div><div class="gmail_default" style="color:#0b5394"><br></div></div><br><div class="gmail_quote gmail_quote_container"><div dir="ltr" class="gmail_attr">On Wed, May 6, 2026 at 9:39 AM Iulian Codreanu <<a href="mailto:codreanu@udel.edu">codreanu@udel.edu</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex">Dear Colleagues,<br>
<br>
I am considering using spin-on dopants for a teaching-type solar cell <br>
project. I am under the impression that these dopants are "messy" and I <br>
am requesting your input on whether they could safely and effectively be <br>
used in one of the our photoresist spinners as opposed to having a <br>
dedicated spinner for this.<br>
<br>
Many thanks.<br>
<br>
-- <br>
iulian Codreanu, Ph.D.<br>
Director, Nanofabrication Facility<br>
University of Delaware<br>
Harker ISE Lab, Room 163<br>
221 Academy Street<br>
Newark, DE 19716<br>
302-831-2784<br>
<a href="https://udnf.udel.edu" rel="noreferrer" target="_blank">https://udnf.udel.edu</a><br>
<br>
<br>
_______________________________________________<br>
labnetwork mailing list<br>
<a href="mailto:labnetwork@mtl.mit.edu" target="_blank">labnetwork@mtl.mit.edu</a><br>
<a href="https://mtl.mit.edu/mailman/listinfo.cgi/labnetwork" rel="noreferrer" target="_blank">https://mtl.mit.edu/mailman/listinfo.cgi/labnetwork</a><br>
</blockquote></div><div><br clear="all"></div><div><br></div><span class="gmail_signature_prefix">-- </span><br><div dir="ltr" class="gmail_signature"><div dir="ltr"><p class="MsoNormal">--<br>
Matthew T. Moneck, Ph.D<br>
Executive Director, Claire & John Bertucci Nanotechnology Laboratory<br>
Electrical & Computer Engineering | Carnegie Mellon University<br>
5000 Forbes Avenue, Pittsburgh, PA 15213-3890<br>
Phone: 412-268-5430<br>
<a href="http://ece.cmu.edu" target="_blank">ece.cmu.edu</a> <br>
<a href="http://nanofab.ece.cmu.edu" target="_blank">nanofab.ece.cmu.edu</a> </p></div></div>